Differences

This shows you the differences between two versions of the page.

--- 3d_prints:instructions:conventional:step4 [2026/03/12 01:13] – created unexpectedlee
+++ 3d_prints:instructions:conventional:step4 [2026/03/13 22:26] (current) – [Step 4.11 – Correctly position the key] unexpectedlee
@@ Line 1: / Line 1: @@
-====== Step 2 –   ======
+====== Step 4 – Install Gear & Drive Shafts  ======
-<WRAP box>
+<WRAP info>
-placeholder
+New Parts needed for this step:
+  - Weight Shaft Key
+  - Weight Shaft
+  - Gearbox Shaft
+  - Brake/Pulley Shaft
+  - Pulley
 </WRAP>
-===== Step 2.1 –   =====
+===== Step 4.1 – Identify the parts  =====
-placeholder
+From left to right, the parts are Weight Shaft Key, Weight Shaft, Gearbox Shaft, Brake/Pulley Shaft (above), and Pulley.
-{{:3d_prints:instructions:conventional:2a.jpg?700}}
+{{:3d_prints:instructions:conventional:4a.jpg?700}}
 -----
-===== Step 2.2 –  =====
+===== Step 4.2 – Install Brake/Pulley Shaft =====
-placeholder
+Install the Brake/Pulley Shaft by inserting it in the rear most socket.  From the rear of the unit, the shaft is inserted on the right side.
-{{:3d_prints:instructions:conventional:2b.jpg?700}}
+<WRAP tip>
+You will need to fiddle with the gear a bit to allow the shaft to slide through.
+</WRAP>
+{{:3d_prints:instructions:conventional:4b.jpg?700}}
 -----
-===== Step 2.3 –  =====
+===== Step 4.3 – Correct orientation =====
-placeholder
+The Pulley goes on the rear left of the unit.
-{{:3d_prints:instructions:conventional:2c.jpg?700}}
+{{:3d_prints:instructions:conventional:4c.jpg?700}}
-<WRAP important>
+-----
-placeholder
+===== Step 4.4 – Install Pulley =====
+Slide the Pulley onto the Pulley/Brake Shaft and into the socket.
+{{:3d_prints:instructions:conventional:4d.jpg?700}}
+-----
+===== Step 4.5 – Align the Gearbox shaft =====
+The gearbox shaft goes in the middle receiver.  It can only be inserted one way.
+<WRAP tip>
+The Gearbox gear may need to be fiddled with as well to allow the Gearbox shaft to slide through.
 </WRAP>
+{{:3d_prints:instructions:conventional:4e.jpg?700}}
 -----
-[[3d_prints:instructions:conventional:step2|⬅ Previous Step]]
+===== Step 4.6 – Insert the gearbox shaft fully =====
-|
-[[3d_prints:instructions:conventional:step4|Next Step ➜]]
+Push the gearbox shaft in completely.
+<WRAP tip>
+The shaft may need to be rotated slightly to be completed inserted.
+</WRAP>
+{{:3d_prints:instructions:conventional:4f.jpg?700}}
+-----
+===== Step 4.7 – Weight shaft installation =====
+Slide the weight shaft through the front most receiver and weight gear.  The weight shaft is bidirectional and can be inserted from either side.
+<WRAP tip>
+Pay attention to the keyhole for the weight shaft key.
+</WRAP>
+{{:3d_prints:instructions:conventional:4g.jpg?700}}
+-----
+===== Step 4.8 – Align the key way =====
+The weight shaft key has a rounded and flat side.  The flat side goes into the weight shaft keyhole.
+<WRAP tip>
+Small fingers or some pliers/tweezers make this step much easier!
+</WRAP>
+{{:3d_prints:instructions:conventional:4h.jpg?700}}
+-----
+===== Step 4.9 – Install weight shaft key =====
+Rotate the gears to align the key way if it is not already aligned.
+{{:3d_prints:instructions:conventional:4i.jpg?700}}
+-----
+===== Step 4.10 – Correctly position the key =====
+Slide the shaft until the key is centered in the gear.
+{{:3d_prints:instructions:conventional:4j.jpg?700}}
+-----
+===== Step 4.11 – View of completed gearbox =====
+{{:3d_prints:instructions:conventional:4k.jpg?700}}
+-----
+<WRAP group>
+<WRAP quarter column>
+[[3d_prints:instructions:conventional:step3|⬅ Previous Step]]
+</WRAP>
+<WRAP right quarter column>
+[[3d_prints:instructions:conventional:step5|Next Step ➜]]
+</WRAP>
+</WRAP>