Differences

This shows you the differences between two versions of the page.

--- 3d_prints:instructions:conventional:step17 [2026/03/12 01:39] – unexpectedlee
+++ 3d_prints:instructions:conventional:step17 [2026/03/14 21:57] (current) – unexpectedlee
@@ Line 1: / Line 1: @@
 ====== Step 17 – Optional Step: Belt Guard  ======
-<WRAP box>
+<WRAP info>
-placeholder
+New Parts needed for this step:
+  - Belt Guard Shroud
+  - Belt Guard Side
 </WRAP>
-===== Step 17.1 –   =====
+===== Step 17.1 – Identify parts =====
-placeholder
+<WRAP info>
+Why is the belt guard optional?  Honestly, it shouldn't be.  However, it is not uncommon to see units operating without all safety features.  To provide you with the ability to display this unit in a way that feels most authentic to you, the belt guard is optional.
+</WRAP>
+The shroud is directly under the pumping unit and the side is at the bottom.  They are in the proper orientation.
 {{:3d_prints:instructions:conventional:17a.jpg?700}}
@@ Line 13: / Line 19: @@
 -----
-===== Step 17.2 –  =====
+===== Step 17.2 – Remove pulleys =====
-placeholder
+Remove the motor and gearbox pulleys.  Often the rubber band will stay in the groves.
 {{:3d_prints:instructions:conventional:17b.jpg?700}}
@@ Line 21: / Line 27: @@
 -----
-===== Step 17.3 –  =====
+===== Step 17.3 – Install gearbox shroud =====
-placeholder
+Install the shroud as shown.  It has no groves and is held in place by the pulleys once they are reinstalled.
 {{:3d_prints:instructions:conventional:17c.jpg?700}}
@@ Line 29: / Line 35: @@
 -----
-===== Step 17.4 –  =====
+===== Step 17.4 – Re-install motor pulley =====
-placeholder
+Reinstall the motor pulley
+<WRAP tip>
+It is much easier to install the pulleys if they are still connected with the rubber band.  If the rubber band did not hold them in place previously, replace the bands in the appropriate pulley groves and stretch slightly to force it into the groves.
+</WRAP>
 {{:3d_prints:instructions:conventional:17d.jpg?700}}
@@ Line 37: / Line 47: @@
 -----
-===== Step 17.5 –  =====
+===== Step 17.5 – Install motor pulley =====
-placeholder
+Install the motor pulley being careful to route the rubber bands around the standoffs.
+<WRAP tip>
+If necessary to reposition fingers, the pulley will typically rest in the proper orientation behind the farthest standoff.
+</WRAP>
 {{:3d_prints:instructions:conventional:17e.jpg?700}}
@@ Line 45: / Line 59: @@
 -----
-===== Step 17.6 –  =====
+===== Step 17.6 – Proper placement =====
-placeholder
+The belts and pulleys should be installed as shown.
 {{:3d_prints:instructions:conventional:17f.jpg?700}}
@@ Line 53: / Line 67: @@
 -----
-===== Step 17.7 –  =====
+===== Step 17.7 – Identify cover attach point =====
-placeholder
+It is easiest to attach the guard by first aligning the rear standoff.
 {{:3d_prints:instructions:conventional:17g.jpg?700}}
@@ Line 61: / Line 75: @@
 -----
-===== Step 17.8 –  =====
+===== Step 17.8 – Attaching the cover =====
-placeholder
+Once aligned, press the cover to attach it to the standoff.
 {{:3d_prints:instructions:conventional:17h.jpg?700}}
@@ Line 69: / Line 83: @@
 -----
-===== Step 17.9 –  =====
+===== Step 17.9 – Final assembly =====
-placeholder
+Once the rear standoff is attached, rotate the cover down and attach to the front standoffs.
 {{:3d_prints:instructions:conventional:17i.jpg?700}}
 -----
+<WRAP group>
+<WRAP quarter column>
 [[3d_prints:instructions:conventional:step16|⬅ Previous Step]]
-|
+</WRAP>
+<WRAP right quarter column>
 [[3d_prints:instructions:conventional:start|Beginning ➜]]
+</WRAP>
+</WRAP>