Differences

This shows you the differences between two versions of the page.

--- 3d_prints:instructions:conventional:parts [2026/03/14 22:22] – unexpectedlee
+++ 3d_prints:instructions:conventional:parts [2026/03/15 14:59] (current) – [Parts List] unexpectedlee
@@ Line 6: / Line 6: @@
 <WRAP third column box center>
-{{:3d_prints:parts:base_frame.jpg?220}}
+{{:3d_prints:instructions:conventional:gearboxbottom.png?220}}
-**Base Frame**
+**Gearbox Bottom**
-Main support structure for the unit.
+Lower housing of the gearbox that supports internal gears and shafts.
+Qty: 1
 </WRAP>
 <WRAP third column box center>
-{{:3d_prints:parts:reducer_base.jpg?220}}
+{{:3d_prints:instructions:conventional:reducerbase.png?220}}
 **Reducer Base**
-Mounting base for the gearbox.
+Mounting base that supports and aligns the gearbox assembly.
+Qty: 1
 </WRAP>
 <WRAP third column box center>
-{{:3d_prints:parts:gearbox.jpg?220}}
+{{:3d_prints:instructions:conventional:base.png?220}}
-**Gearbox**
+**Base**
-Slides onto the reducer base and locks in place.
+Main structural platform supporting the entire pumping unit.
+Qty: 1
+</WRAP>
 </WRAP>
+<WRAP group>
 <WRAP third column box center>
-{{:3d_prints:parts:samson_post.jpg?220}}
+{{:3d_prints:instructions:conventional:crankgear.png?220}}
-**Samson Post**
+**Crank Gear**
+Gear attached to the counterweight shaft that transfers rotational motion.
+Qty: 1
-Vertical support for the walking beam.
 </WRAP>
 <WRAP third column box center>
-{{:3d_prints:parts:walking_beam.jpg?220}}
+{{:3d_prints:instructions:conventional:gearboxgear.png?220}}
-**Walking Beam**
+**Gearbox Gear**
-Transfers motion across the unit.
+Primary drive gear inside the gearbox.
+Qty: 1
 </WRAP>
 <WRAP third column box center>
-{{:3d_prints:parts:horsehead.jpg?220}}
+{{:3d_prints:instructions:conventional:pulleygear.png?220}}
+**Pulley Gear**
+Gear that transfers motion from the pulley drive to the gearbox.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:weightshaftkey.png?220}}
+**Crank Shaft Key**
+Locking key securing the gear to the crank shaft.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:crankshaft.png?220}}
+**Crank Shaft**
+Rotating shaft supporting the counterweight.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:gearboxshaft.png?220}}
+**Gearbox Shaft**
+Internal shaft transmitting rotation through the gearbox.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:reducerpulleyshaft.png?220}}
+**Brake/Reducer Pulley Shaft**
+Shaft supporting the drive pulley assembly.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:reducerpulley.png?220}}
+**Reducer Pulley**
+Rotating wheel transferring belt power to the gearbox.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motor.png?220}}
+**Motor**
+Electric motor that powers the pumping unit mechanism.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motorplatform.png?220}}
+**Motor Platform**
+Mounting platform supporting the motor assembly.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motorplatformlegleft.png?220}}
+**Motor Platform Leg Left**
+Left support leg stabilizing the motor platform.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motorplatformlegright.png?220}}
+**Motor Platform Leg Right**
+Right support leg stabilizing the motor platform.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:postback.png?220}}
+**Post Back**
+Rear support post for the beam structure.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:postleft.png?220}}
+**Post Left**
+Left structural support for the saddle bearing assembly.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:postright.png?220}}
+**Post Right**
+Right structural support for the saddle bearing assembly.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:saddlebearing.png?220}}
+**Saddle Bearing**
+Bearing assembly supporting the walking beam pivot.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:horsehead.png?220}}
 **Horsehead**
-Mounted at the front of the walking beam.
+Curved front piece attached to the walking beam.
+Qty: 1
 </WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:walkingbeam.png?220}}
+**Walking Beam**
+Main beam converting rotary motion into pumping motion.
+Qty: 1
 </WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:saddlebearingpin.png?220}}
+**Saddle Bearing Pin**
+Pin securing the walking beam to the saddle bearing.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:pitmanpin.png?220}}
+**Pitman Pin**
+Pin connecting the pitman arms to the crank assembly.
+Qty: 2
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:equalizerbeam.png?220}}
+**Equalizer Beam**
+Linkage distributing motion between pitman arms.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:pitman.png?220}}
+**Pitman**
+Connecting arm transferring motion from crank to beam.
+Qty: 2
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:equalizerpin.png?220}}
+**Equalizer Pin**
+Pin securing the equalizer linkage.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:crank.png?220}}
+**Crank**
+Rotating arm converting gearbox rotation into reciprocating motion.
+Qty: 2
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:weight.png?220}}
+**Weight**
+Counterweight balancing the pumping unit motion.
+Qty: 4
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:crankpin.png?220}}
+**Crank Pin**
+Pin connecting the pitman arm to the crank.
+Qty: 2
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motorpulley.png?220}}
+**Motor Pulley**
+Pulley mounted on the motor shaft driving the belt.
+Qty: 1
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:motorshaft.png?220}}
+**Motor Shaft**
+Rotating shaft extending from the motor.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:handwheel.png?220}}
+**Hand Wheel**
+Manual wheel used to rotate the mechanism by hand.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:belts.png?220}}
+**Belt**
+Flexible belt transferring power from motor to gearbox.
+Qty: 2
+</WRAP>
+</WRAP>
+<WRAP group>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:beltguardshroud.png?220}}
+**Belt Guard Shroud**
+Protective cover enclosing the belt drive.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:beltguardcover.png?220}}
+**Belt Guard Side**
+Side panel completing the belt guard enclosure.
+Qty: 1
+</WRAP>
+<WRAP third column box center>
+{{:3d_prints:instructions:conventional:gearboxtop.png?220}}
+**Gearbox Top**
+Upper housing cover protecting gearbox components.
+Qty: 1
+</WRAP>
+</WRAP>
 -----
 <WRAP group>